Medical Industry And Plastic Articles & Analysis
14 news found
Many medical devices are manufactured through plastic injection moulding, which allows for precise and top-quality components in large-scale production and better aligns with ISO standards. In general, injection moulding for medical devices is conducted in an ISO 8 clean room environment to ensure all products adhere to the strictest standards of ...
However, in the actual production of medical sterilization paper plastic packaging bags, there are often some problems. ...
Active Implants, a company that develops orthopedic implant solutions, today announced that the company’s SUN (Safety Using NUsurface) trial is now underway in San Diego. Dr. Scott A. Hacker at Grossmont Orthopaedic Medical Group is the only physician in San Diego County – and the center is one of just 10 sites nationwide – participating in the SUN clinical trial to evaluate the ...
Dr. Scott A. Hacker, an expert in arthroscopic surgery, total joint replacements, sports medicine and fracture care, and Active Implants, a company that develops orthopedic implant solutions, today announced that the first meniscus replacement procedure in San Diego has been performed. Dr. Hacker is the only physician in San Diego County – and Grossmont Orthopedic Medical Group is one of ...
The Korea Health Industry Development Institute (KHIDI) announced on the 31st that it held the 'China Pharmaceutical Bio Investment Briefing (IR)' on the 20th, where domestic pharmaceutical companies introduced their technologies to Chinese investors. ...
Active Implants LLC, a company that develops orthopedic implant solutions, today announced that two patients in Israel have undergone knee surgery for the company’s NUsurface® Meniscus Implant – the first “artificial meniscus” to be marketed in the Middle East. Until now, the NUsurface Implant was only available in Israel in clinical trials. The procedures were ...
Jointechlabs – a leader in point-of-care regenerative medicine therapies – today announced that the U.S. Food and Drug Administration (FDA) cleared the company’s MiniTCTM for point-of-care fat tissue processing designed to obtain microfat (or fat grafts), for multiple indications. Jointechlabs plans to focus on a range of therapeutic areas including medical aesthetics, plastic ...
In a Plastics Market Watch report released today, Watching: Plastics’ Contribution to Healthcare, The Plastics Industry Association (PLASTICS) reported a growing demand for plastics in a number of healthcare sectors including pharmaceuticals, surgical equipment and tools, ...
This takes place under the umbrella of Düsseldorf's four major leading global trade fairs – interpack (Processing & Packaging), MEDICA (Health & Medical Technologies), K (Plastics & Rubber) and wire & Tube (Metals & Flow Technologies). ...
TOCA (The Orthopedic Clinic Association), a one-stop resource for orthopedics in Arizona, and Active Implants, a company that develops orthopedic implant solutions, today announced that the first meniscus replacement procedures in Arizona were successfully performed by Dr. Tom Carter. TOCA is the only center in the state – and one of just 10 sites nationwide – enrolling patients with ...
OrthoIndy and Active Implants, a company that develops orthopedic implant solutions, today announced that the first meniscus replacement procedures have been performed in Indiana. Dr. Jack Farr, orthopedic surgeon at OrthoIndy, was the first to perform the procedure on Greenwood resident Jason Scott. OrthoIndy is the only center in the state – and just one of 10 sites nationwide - ...
This guide is intended to provide guidance for the specification and selection of fabrication methods for silicones used in medical devices. It also provides guidance relative to testing that might be done to qualify lots of acceptable material, based on desired performance properties. Silicone manufacturers ...
This specification covers polyoxymethylene (acetal) resin for medical applications. This specification provides requirements and associated test methods for a form of this thermoplastic which is intended for use in manufacturing medical devices, instrumentation or components thereof. Physical and mechanical properties of medical grade ...
Also included are the first in a series of Implementation Modules, resources to assist in implementing best practices in a number of areas: Medical Device Reprocessing OR Kit Reformulation Moving (Back) to Reusables in the OR Regulated Medical Waste Segregation and Minimization in the OR Medical Plastic Recycling in the OR ...