Hip Replacement Equipment & Supplies
65 equipment items found
by:INNOPROOF GmbH based inRostock, GERMANY
In the static burst test, the strength of the ball head is determined in connection with the stem trunnion. After the head has been attached to the stem trunnion with a defined force, a static axially acting load is applied to the head at a fixed rate. A termination criterion is, among others, a breakage of the head. For a successful test, five samples must be tested without failure to a defined ...
Manufactured by:Stora Enso AB based inStockholm, SWEDEN
Plus typically replace polypropylene, HIPS and ABS. Developed with the purpose of being more flexible and impact-resistant than Pure, for items that require increased impact strength and formability.Some of these grades are also food-approved. ...
by:INNOPROOF GmbH based inRostock, GERMANY
The femoral head torque test provides information on the torque required to disassemble the taper connection between a hip stem and head after a defined assembly. This is a static test with a single load ...
Manufactured by:Permedica S.p.A. based inMerate (LC), ITALY
All joint heads presents a 12/14 taper compatible with any femoral stem of Permedica. On special request, joint heads with 10/12 and 14/16 taper are also ...
Manufactured by:Ormed Group Medical based inYenimahalle, TURKEY
OGM Hip Spacers are basically formed by combining antibiotic bone cement with a previously made stainless steel material. It appears as a hip replacement in design. It is in one piece. Locally release gentamicin. It is offered in 2 different sizes, short and long, depending on preference. Both are produced in 4 different diameters. Head diameters are designed as 48/52/56/60 ...
Manufactured by:Euromed Implants GmbH based inStade, GERMANY
Modular Cementless Stem is a well proven implant. It consists of a complete set for primary total hip ...
Manufactured by:Euromed Implants GmbH based inStade, GERMANY
The Almond Modular Cemented Stem is a well proven implant. It consists of a complete set for primary total hip ...
by:INNOPROOF GmbH based inRostock, GERMANY
The tests according to ISO 7206-4 and -6 refer to the shaft or neck area of the femoral component of hip endoprostheses. The fatigue strength of the hip stem is determined under a given sinusoidal load and over a defined number of cycles. The clamping as well as the applied loads differ according to the design of the hip stem, classified as a short, standard or revision stem. Moreover, special ...
Manufactured by:Fuse Medical Inc. based inRichardson, TEXAS (USA)
Designed to facilitate reproducible results allowing total hip replacement patients to return back to their personalized level of activity. Built to achieve optimal alignment, desired leg length, and rotational stability. Streamlined, two-tray instrumentation system to complement the surgical technique. ...
Manufactured by:Zimmer Biomet based inWarsaw, INDIANA (USA)
Zimmer Biomet's E1 Antioxidant Infused Technology is the only bearing option that utilizes a proprietary diffusion process to maxamize strength, wear resistance and prevent oxidative degradation of the ...
by:Vivozon Inc. based inYongin-si, SOUTH KOREA
A randomized, double-blind, parallel group, placebo-controlled clinical trial to evaluate the analgesic efficacy and safety of VVZ-149 Injection in patients who have pain after artificial hip replacement ...
Manufactured by:endocon GmbH based inWiesenbach, GERMANY
The EndoDriver is a proven surgical instrument for total hip replacement femoral components that should be available in every revision surgery. Revision operations are safer and better when scheduled with this instrument. Only a few steps necessary for safe fixation of the instrument to the neck of the prosthesis, Axial force transfer and stable clamping force by patented system, Transfer of ...
Manufactured by:GO German Orthopedic Implants GmbH based inHamburg, GERMANY
For optimal results the surgery should be planned in advance using the appropriate templates. The templates are enlarged by a factor of 110%. The implant size should be choosen using good quality AP and ML X-rays with adequate contrast. Each X-ray should be large enough to apply the whole ...
Manufactured by:TIPMED Medical Device Manufacturing Ltd. Co. based inIzmir, TURKEY
The S2 Modular Hip Prosthesis System is intended to be used as the proximal part of a hip stem arthoplasty. The system is designed to be used for femur fractures of primary hip operated patients. It is totally designed for uncemented ...
Manufactured by:TIPMED Medical Device Manufacturing Ltd. Co. based inIzmir, TURKEY
The S2 Anatomical Modular Hip Prosthesis System is intended to be used as the proximal part of a hip stem arthoplasty. The system is designed to be used for femur fractures of primary hip operated patients. It is totally designed for uncemented application. While neck length increases in the line with the prosthesis ...
Manufactured by:TIPMED Medical Device Manufacturing Ltd. Co. based inIzmir, TURKEY
The S2 Primary Modular Hip Prosthesis System is intended to be used as the proximal part of a hip stem arthoplasty. The system is designed to be used for femur fractures of primary hip operated patients. It is totally designed for uncemented application. While neck length increases in the line with the prosthesis diameter. Optional Ti. plasma spray (PL), HA or Porous coated stems use the ...
Manufactured by:Medacta International based inCastel San Pietro, SWITZERLAND
Quadra System is a straight stem complete system for use in primary and revision ...
Manufactured by:Zimmer Biomet based inWarsaw, INDIANA (USA)
The collarless, polished, double-taper design concept used in the CPT Hip System has proven itself clinically in more than 25 years of use.¹ This distinctive design philosophy is based on the use of natural compressive forces to help ensure that the implant is firmly seated and wedged within the cement mantle. The CPT System, in cobalt-chromium² and stainless steel,3,4 has achieved ...
Manufactured by:GO German Orthopedic Implants GmbH based inHamburg, GERMANY
For optimal results the surgery should be planned in advance using the appropriate templates. The templates are enlarged by a factor of 110%. The implant size should be choosen using good quality AP and ML radiographs with adequate contrast. Radiographs should include a full A/P (anterior/posterior) view of the pelvis, including the proximal one-half of both femurs and a lateral view of the ...
Manufactured by:Orliman S.L.U. based inLa Pobla de Vallbona, SPAIN
Modular hip stabilizing orthosis that can be used interchangeably for the left or right hip. Made of highdensity polyethylene. Comprised of a pelvic band and thigh support (both twin shell), connected by a joint that adjusts flexo-extension from 0º to 80º in increments of 20º, and abduction, in the 0º, 20º and 40º positions. The thigh support allows you to modify the ...