Show results for
Refine by
Hip Replacement Equipment Supplied In Germany
16 equipment items found
Manufactured by:Conformis based inBillerica, MASSACHUSETTS (USA)
The Conformis Hip System, is the only primary total hip replacement system on the market designed with 3D imaging technology to provide a stem and acetabular cup size that matches each patient’s specific ...
Manufactured by:Conformis based inBillerica, MASSACHUSETTS (USA)
Cordera Match Hip System combines the proven Cordera hip stem with Conformis’ state-of-the-art, personalized pre-operative plans and patient-specific ...
Manufactured by:GO German Orthopedic Implants GmbH based inHamburg, GERMANY
The EasyHip Bipolar Head consists of an UHMWPE component encased in an ultra-smooth polished CoCrMo outer metal casing, for articulation in the bony acetabulum. It is to be used in conjunction with femoral components from the GO Implants Total Hip ...
Manufactured by:GO German Orthopedic Implants GmbH based inHamburg, GERMANY
For optimal results the surgery should be planned in advance using the appropriate templates. The templates are enlarged by a factor of 110%. The implant size should be choosen using good quality AP and ML X-rays with adequate contrast. Each X-ray should be large enough to apply the whole ...
Manufactured by:GO German Orthopedic Implants GmbH based inHamburg, GERMANY
For optimal results the surgery should be planned in advance using the appropriate templates. The templates are enlarged by a factor of 110%. The implant size should be choosen using good quality AP and ML radiographs with adequate contrast. Radiographs should include a full A/P (anterior/posterior) view of the pelvis, including the proximal one-half of both femurs and a lateral view of the ...
Manufactured by:GO German Orthopedic Implants GmbH based inHamburg, GERMANY
for total hip arthroplasty are small ceramic balls that are placed onto the hip stem. Due to the conical design of the 12/14 taper, the heads sit firmly on the stem and require no additional fixation. EasyHip Ceramic Heads come in three diameters (28 mm, 32 mm and 36 mm) and four head neck lengths, ranging from -4 mm to +8 mm. Detailed correlation can be seen in table ...
Manufactured by:GO German Orthopedic Implants GmbH based inHamburg, GERMANY
All surgical approaches can be used while implanting EasyHip Cementless Cups components. All the following steps apply for postero-lateral surgical approach and all other surgical access routes. The patient lies on his/her side. The incision is done postero-laterally. After opening of the fascia-lata, external rotator muscles are resected and the joint capsule is incited. Then, the femoral head ...
Manufactured by:GO German Orthopedic Implants GmbH based inHamburg, GERMANY
All the cemented Acetabular Cups can be implanted via any standard approach for total hip arthroplasty, depending on the surgeon's level of ...
by:INNOPROOF GmbH based inRostock, GERMANY
In the static burst test, the strength of the ball head is determined in connection with the stem trunnion. After the head has been attached to the stem trunnion with a defined force, a static axially acting load is applied to the head at a fixed rate. A termination criterion is, among others, a breakage of the head. For a successful test, five samples must be tested without failure to a defined ...
by:INNOPROOF GmbH based inRostock, GERMANY
The femoral head torque test provides information on the torque required to disassemble the taper connection between a hip stem and head after a defined assembly. This is a static test with a single load ...
by:INNOPROOF GmbH based inRostock, GERMANY
The tests according to ISO 7206-4 and -6 refer to the shaft or neck area of the femoral component of hip endoprostheses. The fatigue strength of the hip stem is determined under a given sinusoidal load and over a defined number of cycles. The clamping as well as the applied loads differ according to the design of the hip stem, classified as a short, standard or revision stem. Moreover, special ...
Manufactured by:Euromed Implants GmbH based inStade, GERMANY
Modular Cementless Stem is a well proven implant. It consists of a complete set for primary total hip ...
Manufactured by:Euromed Implants GmbH based inStade, GERMANY
The Almond Modular Cemented Stem is a well proven implant. It consists of a complete set for primary total hip ...
Manufactured by:endocon GmbH based inWiesenbach, GERMANY
The EndoDriver is a proven surgical instrument for total hip replacement femoral components that should be available in every revision surgery. Revision operations are safer and better when scheduled with this instrument. Only a few steps necessary for safe fixation of the instrument to the neck of the prosthesis, Axial force transfer and stable clamping force by ...
Manufactured by:Baymed Inovative Health Products Inc. based inMerkez/Kilis, TURKEY
Baymed® disposable orthopaedic drapes offer optimum combination of features to meet the rigorous demands of orthopaedic surgery, from hand procedures to hip replacement. They provide added protection and are made with heavy-duty fabric. Designed for safety and convenience, they also feature Bayteks® advcanced reinforcement fabrics for fluid management. ...
Manufactured by:Heraeus Medical GmbH based inWehrheim, GERMANY
Its distinctive green color is due to the inclusion of colorant E141. This product offers a broad spectrum of activity against pathogens that cause infections post-hip and knee replacement surgeries. The simultaneous release of gentamicin and clindamycin addresses up to 90% of pathogens found in prosthetic joint infections (PJI). It provides an initial high local ...